Integra; DTR-7.8; Integra DTR-7.8. Below you will found our manuals on the Integra DTR-7.8. The owners manual is used as an reference guide, instruction manual and instruction book. The service manual functions as a repair guide for troubleshooting and sometimes contains tips for. Integra DTR-7.8 User Manual. Specifications. Integra Receivers and Amplifiers. Manuals Directory ManualsDir.com - online owner manuals library. Integra manuals. Receivers and Amplifiers. Manual Specifications – Integra DTR-7.8 User Manual Page 127.
- Integra Dtr 7.8 Manual
- Integra Dtr 5.8 Review
- Integra Dtr 7.2
- User Manual Pdf
- Integra Dtr 7.8 Specs
- User Manual Template
126
Troubleshooting
—Continued
• Listen to the station in mono (page 61).
• When listening to an AM station, operating the remote
controller may cause noise.
• Passing cars and airplanes can cause interference.
• Concrete walls weaken radio signals.
• If nothing improves the reception, install an outdoor
antenna.
The remote controller doesn’t work
• Make sure that the batteries are installed with the cor-
• Make sure that the remote controller is not too far
away from the AV receiver and there’s no obstruction
between the remote controller and the AV receiver’s
remote control sensor (page 14).
• Make sure you’ve selected the correct remote control-
• Make sure you’ve entered the correct remote control
Can’t control other components
• Make sure you’ve selected the correct remote control-
• If you’ve connected an
-capable Onkyo MD
recorder, CD recorder, or RI Dock to the TAPE
IN/OUT jacks, or an RI Dock to the GAME/TV IN
jacks, for the remote controller to work properly, you
must set the Input Display to MD, CDR, or DOCK,
respectively (see page 49).
• The entered remote control code may not be correct. If
more than one code is listed, try each one.
• If none of the codes work, use the Learning function
to learn the commands of the other component’s
remote controller (page 122).
• With some AV components, certain buttons may not
work as expected, and some may not work at all.
• To control an Integra/Onkyo component that’s con-
nected via
, point the remote controller at the AV
receiver. Be sure to enter the appropriate remote con-
trol code first (page 120).
• To control an Integra/Onkyo component that’s not
connected via
Integra Dtr 7.8 Manual
, or another manufacturer’s compo-
nent, point the remote controller at that component. Be
sure to enter the appropriate remote control code first
(page 119).
Can’t learn commands from another remote
controller
• When learning commands, make sure that the trans-
mitting ends of both remote controllers are pointing at
each other.
• Are you trying to learn from a remote controller that
cannot be used for learning? Some commands cannot
be learned, especially those that contain several
instructions.
Integra Dtr 5.8 Review
Can’t record
• On your recorder, make sure the correct input is
selected.
• To prevent signal loops and damage to the AV
receiver, input signals are not fed through to outputs
with the same name (e.g., TAPE IN to TAPE OUT or
VCR/DVR IN to VCR/DVR OUT).
The sound changes when I connect my head-
phones
• When a pair of headphones is connected, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono, or Direct, in which case it stays the same.
How do I change the language of a multiplex
source
• On the Audio Adjust menu, change the Multiplex set-
The
functions don’t work
Integra Dtr 7.2
• To use
, you must make an
connection and an
analog audio connection (RCA) between the compo-
nent and AV receiver, even if they are connected digi-
tally (page 42).
• While Zone 2 or Zone 3 is selected, the
functions
don’t work.
Components connected to the AV receiver’s AC
outlets don’t turn on or off when the AV receiver
is set to On or Standby
• When the HDMI Control setting is set to Enable
(page 109), the AC outlets are on all the time regard-
less of whether the AV receiver is set to On or Standby,
or Ready mode in this case, so any components con-
nected to them cannot be turned on or off automati-
cally.
User Manual Pdf
Remote Controller
Recording
Others
The AV receiver contains a microcomputer for signal pro-
cessing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least 5 seconds, and then plug it back
in again.
Integra Dtr 7.8 Specs
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
this unit’s malfunction. Before you record important
data, make sure that the material will be recorded cor-
rectly.
Set the AV receiver to Standby before disconnecting
the power cord from the wall outlet.