Black And Decker Edge Hog User Manual

  1. Black And Decker Edge Hog Eh1000 Manual
  2. Black And Decker Edge Hog Manual
  3. Black & Decker Edge Hog Edger Manual

The Black and Decker Edge Hog edger tool makes quick work of cutting edges along a flowerbed, walkway, patio or driveway. The Edge Hog is powered by an electric motor, allowing you to use the edger without the noise and exhaust fumes the machine would produce if it were a gasoline-powered model. The Edge Hog also can be used as a landscape trencher and to cut through grass and soil to allow for the removal of sod. Use the Edge Hog as part of your regular lawn-maintenance routine to keep landscape edges looking crisp and clean.

1

Page 3 of Black & Decker Edger EDGE HOG. Find product support and user manuals for your Black & Decker Edger EDGE HOG, and save it to your Product Collection. Product Support made simple from Do It. 12 Amp 2-in-1 Landscape Edger and Trencher. Contact Support Instruction Manual Repair Find Parts Register Your Product Live Chat. Fueled by electric power, BLACK+DECKER outdoor equipment gives you the power you need without the fumes and mess of gas. It also produces no emissions while in use, helping to keep the air we breathe cleaner.

Push the Edge Hog onto a solid surface, such as a sidewalk or driveway. Find the cut-depth knob, which is on the edger's front, directly next to the front wheel. Turn the cut-depth knob counterclockwise by hand, loosening the knob.

2

Pull the front wheel outward to lower the blade's cutting depth, or push the front wheel inward to raise the blade's cutting depth. Raise or lower the front wheel until the arrow on the front wheel bracket lines up with the 1-inch mark on the front housing.

3

Turn the cut-depth knob fully clockwise by hand, tightening the knob. This task secures the front wheel and the blade's cutting depth in place.

4

Lower the Edge Hog's cutting blade edge guide. Tilt the edger tool handle back, raising the front of the edger, and allow the edge guide to be lowered. Grasp the edge guide handle, and push it to the right, unlocking the handle from the locking guide tab.

5

Push the edge guide knob down until the upper square notch in the lever lines up with the locking guide tab. Release the edge guide handle to lock the edge guide into position. It may be necessary to raise the edge guide all the way up to start the edger on thick grass and to edge along garden beds.

6

Plug the edger's power cord into an electrical extension cord. Plug the extension cord into an independent electrical circuit, such as a ground-fault circuit interrupter outlet. Position the power cord on the side opposite the cutting blade to prevent damage to the cord.

7

Place the edger's cutting blade in line with the side of a paved, concrete or other hard surface you want to edge. When you edge along a hard surface, the edger's rear wheel should remain on that hard surface. When edging along a flowerbed or similar area, position the blade on the inside of that area so the rest of the edger can be pushed along the grass.

8

Lower the Edge Hog's handle somewhat, tilting the edger and raising its cutting blade above the soil surface. Switch on the edger. Allow the cutting blade to reach full speed.

9

Lower the cutting blade into the soil along the hard surface's edge. Push the edger slowly, with the cutting blade slightly pressed against the hard surface's edge. Continue to edge along the hard surface as desired.

10

Pull the edger backward about 2 to 3 inches if the cutting blade begins to slow or bind. Allow the blade to return to normal speed before continuing to use the edger. The cutting blade may slow or bind in thick grass, especially at the beginning of the edging and lawn mowing season. Regular lawn and edging maintenance makes the problem less likely throughout the season.

Tip

  • Avoid operating the Edge Hog when the grass is wet because wet grass can clog an edger and damage its blade.

References (2)

About the Author

A former cake decorator and competitive horticulturist, Amelia Allonsy is most at home in the kitchen or with her hands in the dirt. She received her Bachelor's degree from West Virginia University. Her work has been published in the San Francisco Chronicle and on other websites.

Cite this Article
Choose Citation Style
Allonsy, Amelia. 'How to Use the Black & Decker Edge Hog.' Home Guides | SF Gate, http://homeguides.sfgate.com/use-black-decker-edge-hog-100249.html. Accessed 11 December 2019.
Allonsy, Amelia. (n.d.). How to Use the Black & Decker Edge Hog. Home Guides | SF Gate. Retrieved from http://homeguides.sfgate.com/use-black-decker-edge-hog-100249.html
Allonsy, Amelia. 'How to Use the Black & Decker Edge Hog' accessed December 11, 2019. http://homeguides.sfgate.com/use-black-decker-edge-hog-100249.html
Note: Depending on which text editor you're pasting into, you might have to add the italics to the site name.

Instruction manual, Lift for trenching lower for edging

Advertising

SAFETY WARNINGS AND INSTRUCTIONS: DOUBLE INSULATION

REPLACEMENT PARTS:

When servicing use only identical Black & Decker replacement parts.

IMPORTANT SAFETY INSTRUCTIONS: POLARIZED PLUGS

To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This

equipment must be used with a suitable polarized 2 wire or 3 wire extension cord. Polarized connections will fit

together only one way. Make sure that the receptacle end of the extension cord has large and small blade slot widths. If

the plug does not fit fully into the extension cord, reverse the plug. If it still does not fit, obtain a suitable extension cord.

If the extension cord does not fit fully into the outlet, contact a qualified electrician to install the proper outlet. Do not

modify the appliance plug or extension cord in any way.
THIS TOOL CAN BE DANGEROUS.

Follow all warnings and Safety Instructions in this manual. The operator is

responsible for following warnings and instructions in this manual and on unit. Restrict use of this power tool to persons
who read, understand and follow warnings and instructions in this manual and on unit.

AVOID DANGEROUS ENVIRONMENT. Don’t use appliances in damp or wet locations. Don’t use appliances in the rain.
KEEP CHILDREN AWAY. All other persons and pets should be kept at a safe distance from work area.
STORE IDLE APPLIANCES INDOORS. Appliances should be stored indoors in dry, secured area – out of reach of children.
DON’T FORCE APPLIANCE. It will do the job better and with less likelihood of a risk of injury at the rate for which it

was designed.

USE RIGHT APPLIANCE. Do not use the appliance for any job except that for which it is intended.
DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves,

long pants and substantial, non-skid footwear are recommended when working outdoors. Do not go barefoot
or wear sandals. Wear protective hair covering to contain long hair.

USE SAFETY GLASSES AND OTHER SAFETY EQUIPMENT. Use safety goggles or safety glasses with side shields,

complying with applicable safety standards and, when needed, a face shield. Also use face or dust mask if operation

is dusty. This applies to all persons in the work area. Also use a hard hat, hearing protection, gloves, safety shoes and

dust collection systems when specified or required. Safety glasses or the like are available at extra cost at your local

dealer or Black & Decker Service Center.

DON’T ABUSE CORD. Never carry appliance by cord or yank it to disconnect from receptacle. Keep cord from

heat, oil, and sharp edges.

DON’T OVERREACH. Keep proper footing and balance at all times.
MAINTAIN APPLIANCE WITH CARE. Keep cutting edge clean for best performance and to reduce the risk of injury.

Follow instructions for lubricating and changing accessories. Inspect appliance cord periodically and if damaged,

have it repaired by authorized service facility. Inspect extension cords periodically and replace if damaged. Keep

handles dry, clean, and free from oil and grease.

DISCONNECT APPLIANCES. Disconnect the appliance from the power supply when not in use, before servicing, and

when changing accessories such as blades and the like.

AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in appliance with finger on switch. Be sure switch is

off when plugging in.

EXTENSION CORDS. Make sure your extension cord is in good condition. Cord insulation must be intact with no cracks or

deterioration. Plug connectors must be undamaged. When using an extension cord, be sure to use one heavy enough to

carry the current your product will draw. An undersized extension cord will cause a drop in line voltage resulting in loss

of power and overheating, which can shorten the life of the motor. The table shows the correct size to use depending on

cord length and nameplate ampere rating. If in doubt, use the next heavier gage.

The smaller the gage number, the heavier the cord. The table shows the correct size to use depending on cord length

and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.

indicates the Edger is DOUBLE INSULATED”

OUTDOOR USE EXTENSION CORDS

Decker

WARNING:

To reduce the risk of electric shock, use only with an extension

cord intended for outdoor use, such as an extension cord of type SW-A, SOW-A, STW-A, STOW-A, SJW-A,

SJOW-A, SJTW-A, or SJTOW-A.

GROUND FAULT CIRCUIT INTERRUPTER (GFCI) protection should be provided on the circuits or outlets to be used for

the gardening appliance. Receptacles are available having built in GFCI protection and may be used for this

measure of safety.

STAY ALERT. Watch what you are doing. Use common sense. Do not operate appliance when you are tired, ill or

under the influence of any drugs or alcohol.

CHECK DAMAGED PARTS. Before further use of the appliance, a guard or other part that is damaged should be

carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of

moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its

operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service

center unless otherwise indicated elsewhere in this manual.

REPAIRS AND SERVICE. Repairs, maintenance and any adjustments not specified in this manual should be performed

by Black & Decker authorized service centers or other qualified service organizations, always using identical

replacement parts.

LI

F

T

F

O

R

TRE

NCHING

LOWER

F

O

R

E

DGING

USE OF ACCESSORIES AND ATTACHMENTS. The use of any accessory or attachment not recommended for use with

this appliance could be hazardous. Note: Refer to the accessory section of this manual for further details.

ADDITIONAL WARNINGS FOR EDGERS

1. Keep guard in place.

2. Keep blade area clean.

DANGER

: Risk of injury. Keep hands and feet away from blade and cutting area.

Important Warning

When using the edger, stones, pieces of metal and other objects can be thrown out at high speed by the blade. The

tool and guard are designed to reduce the danger. However, the following special precautions should be taken:

1. Wear safety glasses or other eye protection, gloves, long pants and substantial footwear.

2. Make sure that other persons and pets are at least 100 feet away.

3. Always stand to left side of main handle.

4. Before Landscaping or Trenching, check for buried electrical cables.

5. To reduce the risk of rebound (ricochet) injury, work going away from any nearby solid object such as a wall,

steps, large stone, tree, etc. Use great care when working close to solid objects or into the wind, and, where

necessary, do edging or trimming by hand.

SAVE THESE INSTRUCTIONS

KEY INFORMATION YOU SHOULD KNOW:

• Your edger is designed to eject clippings and other debris forward, away from the operator.
• Inspect and thoroughly clean your edger at the start of each edging season.
• The blade on this tool is not intended to be sharp. Do not sharpen it in any way.
• Make sure edging area (100 ft.) is clear of other persons or pets prior to starting operation.

SAVE THIS MANUAL FOR FUTURE REFERENCE

Cat No. LE750 Type 2 & 3

Form No. 243420-02 Rev. 4

SEPT. ‘02

Copyright © 2002 Black & Decker

Printed in Mexico

LE750 TYPE 2 & 3

Minimum Gage for Cord Sets

Volts

Total Length of Cord in Feet

120V

0-25

26-50

51-100

101-150

240V

0-50

51-100

101-200

201-300

Ampere Rating

More

Not more

Manual

American Wire Gage

Than

Than

0

-

6

18

16

16

14

6

-

10

18

16

14

12

10 -

12

16

16

14

12

12 -

16

14

12

Not Recommended

1

A

B

C

D

3

2

4

1.5

1.25

1.0

D

E

P

T

H

5

LIFT

FOR

TRENCHING

LOWER FOR

EDGING

6

7

8

9

11

10

Black And Decker Edge Hog Eh1000 Manual

Hex nut with conical washer
Écrou hexagonal muni d’une rondelle conique

Tuerca hexagonal con roldana conica

INSTRUCTION MANUAL

ASSEMBLY INSTRUCTIONS

BEFORE ASSEMBLING YOUR EDGER, CHECK THAT YOU HAVE RECEIVED THE FOLLOWING IN THE SHIPPING
CARTON.

SEE FIGURE 1.
A. LE750 Landscape/Edger
B. Edge Hog blade with nut, conical washer and spacer system (assembled to unit)
C. Tube connecting bolt and knob (assembled to lower tube)
D. Auxiliary Handle, with bolt and knob

ASSEMBLING THE HANDLE
Assemble Handle Tubes (Figure 2 and 3)

1. Remove knob and curved head bolt from lower handle tube mounting holes.
2. Slide upper handle tube down into lower handle tube so that holes will line up (Figure 3). There are two

positions available for adjustment to your preferred height setting. See Figure 11 for upper handle orientation.

3. NOTE: Ensure the wire cable moves smoothly down into the lower handle tube while assembling.
4. Fasten handle tubes together with the knob and curved head bolt. Note that when you first insert the bolt

it may be necessary to wiggle it carefully to get it past the jacketed wire inside the tube.

CAUTION:

NEVER use a sharp object to move jacketed wires out of the way.

Position Auxiliary Handle (Figure 4)

1. Undo the knob from the bolt in the auxiliary handle and push/pull the bolt out of the handle.
2. Slide the auxiliary handle onto the main handle. The auxiliary handle can be positioned for either left or

right-hand operation whichever is more comfortable. The auxiliary handle is NOT adjustable forward/back.

3. Insert the bolt back into the auxiliary handle hole on the side with the hex recess, attach the knob and fully tighten.

Cut Depth Adjustment (Figure 5)

The front wheel can be adjusted to allow a deeper or shallower cut, and to increase the life of the blade. Change the

cut depth from the shipping position to your desired depth by:
1. Wait for blade to come to complete stop!
2. UNPLUG TOOL!
3. Loosen the Cut Depth Knob.
4. Adjust wheel depth, using the depth indicator on the wheel bracket and the marking on the front housing.
Note: Recommend 1” depth for edging.
5. Tighten Knob firmly.

Tip: Thick overgrowth may drag on the guard. Reduce cut depth to minimum to help reduce this effect.

Pull-Up Edge Guide (Figure 6, 7)

The edge guide is useful for cutting a straight path along sidewalks. For landscaping or trenching in the yard the edge

guide can interfere with moving the edger through hard soil or sod. The edge guide can be adjusted so that the tool

will also perform TRENCHING and LANDSCAPING operations.

To Change Position Of The Edge Guide

1. Wait for blade to come to complete stop!
2. UNPLUG TOOL!
3. Pull Edge Guide Knob sideways to unlock from the guard tab, see Figure 6 detail, in direction of small arrow. Lift

the knob up until the lower square notch in the lever lines up with the tab on the guard. In this position the edge

guide is lifted up (Figure 7) so the tool can easily cut along the edges of flower and shrubbery beds, and around

trees in preparation for trenching or sod removal.

4. To return edge guide to lower position, pull lever sideways and push down until guard tab fits into upper lever hole.

Black And Decker Edge Hog Manual

Tip: You may need to tilt edger back to allow edge guide to be moved into down position.

Attaching Extension Cord To Edger (Figure 8)

Important Safety Instructions: Polarized Plugs

To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). Do not

modify the appliance plug or extension cord in any way. Read IMPORTANT SAFETY INSTRUCTIONS at beginning of

manual. Note: Check the extension cord safety instructions provided earlier.
1. To prevent disconnection of edger cord, secure extension cord by tying the power plug as shown.
2. Insert plug into cord socket.
3. An extension cord retainer is built into the switch handle to reduce strain on the power cord. To use this feature,

simply double the extension cord as shown, about a foot from the end, and insert it into the end of the handle. Hook

9A

12

13

WARNING: Important Safety Warnings and Instructions
WARNING:

When using electric gardening appliances, basic safety precautions should always be followed to

reduce risk of fire, electric shock, and personal injury, including the following.

WARNING:

Some dust created by this product contains chemicals known to the State of California to cause

cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• compounds in fertilizers

• compounds in insecticides, herbicides and pesticides

• arsenic and chromium from chemically treated lumber

To reduce your exposure to these chemicals, wear approved safety equipment such as dust masks that are specially

designed to filter out microscopic particles.

WARNING:

This product contains chemicals, including lead, known to the State of California to cause cancer,

and birth defects or other reproductive harm. Wash hands after handling.

CAUTION:

Wear appropriate personal hearing protection during use. Under some conditions and duration of

use, noise from this product may contribute to hearing loss.

READ ALL INSTRUCTIONS

TO REDUCE RISK OF INJURY:

• Before any use, be sure everyone using this tool reads and understands all safety instructions and other information

contained in this manual.

• Save these instructions and review frequently prior to use and in instructing others.

GENERAL SAFETY WARNINGS AND INSTRUCTIONS FOR ALL TOOLS

1-800-54-HOW-TO (544-6986)

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

IF YOU SHOULD EXPERIENCE A PROBLEM

WITH YOUR BLACK & DECKER PRODUCT,

CALL 1-800-54-HOW-TO (544-6986).

BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION

AVAILABLE, CATALOG NO., TYPE NO. AND DATE CODE.

IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CAN

RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE A

SUGGESTION OR COMMENT, GIVE US A CALL.YOUR FEEDBACK

Black & Decker Edge Hog Edger Manual

IS VITAL TO THE SUCCESS OF BLACK & DECKER.

Advertising
Popular Brands
Popular manuals